Page 1 of 3

Dying bricks with Vinyl Dye - the result

Posted: Wed Nov 16, 2005 4:37 am
by SavaTheAggie
On Sunday I went out and bought a can of Vinyl and Plastic 'Coating'. It was the only product for Vinyl both Wal Mart and Autozone carries. I also bought a KK2 set with the red knight to experiment. The product I bought was:

Dupli-Color Vinyl & Fabric Coating (coating in really tiny letters... a clue!)

And here is our poor test subject:

Image

Now I followed the directions I had read online about dying computer cover parts, spraying about 12 inches away in a sweeping motion. I took five minute breaks, allowing the 'coating' to dry.

Well, what I got resembles stone. Not bad, but definately not what I was going for.

So I went to a different website, one with close up pictures, and it definately looked nothing like what I had, and everything I was trying to achieve. I obviously had not bought genuine Vinyl Dye.

So once again I went out, this time to O'Reilly's auto parts. Hidden on a shelf, not with the paints, was a product called:

Mar-Hyde Vinyl Color Spray

This stuff looked like the real deal. The first named ingrediant? Acetone! That's right, everyone's favorite plastic-melting compound.

From what I read, this is exactly what I wanted.

So I bit the bullet, and subjected my favorite KK2 knight, the purple one, to the knife, so to speak.

Image

Once again, I followed the same procedure - long distance sweeping motions, taking breaks between. This new stuff said it dries in 15 minutes, and can be subjected to weather in 2 hours. The other can didn't even mention a time frame.

So the result? I know you're tired of my write up.

Here are the two visors. Remember, the red knight's visor (right) got the Vinyl "Coating", while the purple knight's visor (left) got the Vinyl Dye.

Without Flash:
Image

With Flash:
Image

Modeling the product:
Image

The purple knight's visor's color most closely resembles new dark bley, from what I can tell. Not too bad, I must say. Its' very smooth, it hardly looks like it got a color treatment at all. I didn't even have to pre-coat it in white.

I know that O'Reilly's sells black, off-white, tan, dark blue, and this 'silver smoke'. There are many websites that offer a much broader color range, but their cans were $17 each. The Stone-like 'coating' cost me $3.50, the Vinyl Dye cost me $4.50.

--Anthony

Posted: Wed Nov 16, 2005 4:51 am
by JoshWedin
That is an interesting product. The second one definitely looks better on the visor, but think the first one could have some interesting applications too.

Thanks!
Josh

Posted: Wed Nov 16, 2005 4:53 am
by lil Jon
Hmm, those are some interesting results.

One complaint, I couldn't really see the colors that well. I'd suggest taking pictures on a nice and sunny day.

Did anything happen to the plastic, like it getting soft and weak, or brittle?

Posted: Wed Nov 16, 2005 1:28 pm
by Suvied
Is it still purple on the inside?

Posted: Wed Nov 16, 2005 1:33 pm
by kingkastle
OHHHHHHHHHHHHHHHHHHH. they both look very nice indeed. Purple knight definitely looks better for use as an actual knight. Red knight definitely looks useable as a statue. Will have to find me some of this stuff. One question though. Did you spray inside the helmet as well? Just interested as to if or if not the plastic becomes any larger with this coating of vinyl paint? I know you stated that vinyl paint absorbs into the plastic. But if one were to use it on, say, a minifig head and helmet would they still fit together??

Posted: Wed Nov 16, 2005 2:01 pm
by ottoatm
Wow... this worked really well on both counts! The purple knight looks very official, as others have said - but I actually prefer the first knight... he seems like the perfect horde knight, or some sort of barbarian.

This was a very nice experiment - I'm tempted to get some of the other colors now that I've seen what you've managed to pull off.

Posted: Wed Nov 16, 2005 3:00 pm
by Morgan19
Oooo those are nice. I kind of like the first one too, for a specific use like someone else mentioned– it'd be neat to construct a statue (figure, base, etc.) and then spray the whole thing at once. I bet that'd look nice and stony.

Mmmm, ideas!

m19

Posted: Wed Nov 16, 2005 3:52 pm
by Tanotrooper
cool

Posted: Wed Nov 16, 2005 6:38 pm
by MaxiVisVires
Now does the color of the plastic had anything to do with how the treatment of the dyes turned out? Did the texture of the plastic change?

Overall a very nice looking effect. :D

Posted: Wed Nov 16, 2005 6:58 pm
by HenrytheV
Too bad there's no O'Reilly car part store near me. Both of them look really good in my opinion, with the second one looking smoother, and the first one looking like he has a textured stone effect. Great experiment Anthony :D

HenrytheV

Posted: Wed Nov 16, 2005 9:05 pm
by SavaTheAggie
lil Jon wrote:Did anything happen to the plastic, like it getting soft and weak, or brittle?
Nope, the plastic is just as it was before.
Suvied wrote:Is it still purple on the inside?
Not for long. I first need to build a rig (probably just a vertical toothpick or bent paperclips) to hold the visor off the ground slightly, just so it doesn't sit in the excess dye (the dye dries like paint if it is not absorbed into a porous material).
kingkastle wrote:One question though. Did you spray inside the helmet as well? Just interested as to if or if not the plastic becomes any larger with this coating of vinyl paint? I know you stated that vinyl paint absorbs into the plastic. But if one were to use it on, say, a minifig head and helmet would they still fit together??
I don't see why not. I did not observe any sort of build-up or any related growth in dimensions on the purple visor. The red visor, on the other hand, does have a noticeable layer.
MaxiVisVires wrote:Now does the color of the plastic had anything to do with how the treatment of the dyes turned out? Did the texture of the plastic change?
I thought the color of the plastic mattered at first, because the color on the purple visor is much darker than the color on the can, but looking back at my aluminum foil, the excess dye is the same color. My conclusion is that as far as purple is concerned, the color did not play any role in the final color outcome.

As for texture, the red visor has a very stoney texture, very rough, but that wasn't Vinyl Dye I used. The Purple visor doesn't have any decernable texture, though the gloss has been dulled down.
HenrytheV wrote:Too bad there's no O'Reilly car part store near me.
You should be able to find Vinyl Dye at any larger auto parts store. Heck, even mom and pop auto part stores sell em around here (now that I know). Plasti-Kote is the brand of choice by the feller whom I learned about Vinyl Dye. After looking at their website I know of 6 places locally that sell that brand.

--Anthony

Posted: Thu Nov 17, 2005 4:20 am
by SavaTheAggie
Well folks... I don't know what to say.

So I'll just let you make your own conclusions.

Image

--Anthony

EDIT: Lenny pointed out I didn't specifically say what color I used. The name of it is "Silver Smoke" of the Mar-Hyde Vinyl COlor Spray.

If you're REALLY looking into the coating stuff that makes the stone look, it's called "Medium Gray"

Posted: Thu Nov 17, 2005 4:49 am
by MaxiVisVires
SavaTheAggie wrote:Well folks... I don't know what to say.

So I'll just let you make your own conclusions.

Image

--Anthony

EDIT: Lenny pointed out I didn't specifically say what color I used. The name of it is "Silver Smoke" of the Mar-Hyde Vinyl COlor Spray.

If you're REALLY looking into the coating stuff that makes the stone look, it's called "Medium Gray"
That looks like Dark Gray to me...

Posted: Thu Nov 17, 2005 2:59 pm
by Tanotrooper
gotta find some of this stuff!

Ave!

Posted: Fri Nov 18, 2005 9:32 pm
by LEGOFREAK
Wow. I have been really out of the loop for a bit.
both visors are interesting (a stone armored group would be wild!) but I am interested in getting some of this vinyl dye. I thought it was just paint.
So does it actually bond with the plastic then? with paint, you can get something to take paint off with (I had some stuff that didnt melt the plastic) and repaint it if you want, but I gather the dye is permanent?
seems a better deal to me...

:D